May 11, 2020 0 Comments

Stay on your feet with slip-resistant footwear. There are some standards, but you can learn about them right here!. Find the most up-to-date version of ASTM F at Engineering Liners · The SYNC System™ Shells · Workbrutes® G2 · Workreation® · About Us · News · Catalogs · Distributor Login · Locate Distributor · Home / ASTM F .

Author: Faulkis Voodoozil
Country: Papua New Guinea
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 16 July 2018
Pages: 369
PDF File Size: 7.27 Mb
ePub File Size: 15.14 Mb
ISBN: 637-1-58428-642-5
Downloads: 21318
Price: Free* [*Free Regsitration Required]
Uploader: Salabar

Various combinations of floor and footwear are possible. The method uses a Mark I, which are not readily produced. The method utilizes the whole shoe, so it seems to offer a more complete picture than those c489 which require sections of the footwear to be tested.

The proliferation of standards creates confusion by both consumers of slip-resistance testing services and even those offering such services.

ASTM F – 96 Standard Test Method for Using a James Machine

Reducing the risk of footwear slip is a critical safety aspect to be considered. The method understates the slip-resistance when used in wet testing. Additional information can be entered through the machine keyboard, allowing test criteria and other relevant data to be included.

This website uses cookies. This standard addresses the recommended format and content of reports addressing slip resistance evaluations.

How can we help? The SATRA STM has been developed with the benefit of extensive research into slip and slip testing methods, together with the experience gained from the daily practical use of the machine in the SATRA footwear testing laboratories. Footwear set in STM cradle prior to slip testing. A slip test machine can be used as a development tool to verify the slip resistance of new footwear products. A proposed standard for Subpart D does make a reference to a 0.

Because most slips and falls occur on contaminated water surfaces, the value of measuring dry COF is limited. The results shall be available at the site and to the steel erector.

  EPOS2 24 5 PDF

This term is largely left undefined. The frame is adjustable to allow the inclination of the footwear to be set relative to the flooring. Such documentation or certification shall be based on the appropriate ASTM standard test method conducted by a laboratory capable of performing the test.

This allows the conditions of slip to be determined in different stages of the walking gait — for example, heel strike, forepart lift-off, or shoe flat to floor. Once initiated, the program brings the footwear into contact with the test surface and applies a pre-set vertical load before translating the floor horizontally at a controlled speed.

To simulate cold weather conditions, an optional piece of SATRA equipment allows a temperature-controlled block of ice to be produced and used in the STM slip test machine. Slip resistance testing is a complex process, and an effective slip test machine needs to control and measure a number of key criteria reproducing the critical factors relating to slip when walking. This device has not be put through a F approval to date.

Using the new ASTM slip standard

The is the testing method which was specific to the Aastm XL tribometer. The testing method however, is still valid and an effective way to evaluate hazards on floors.

It is common to asm footwear against a dry floor and wet floor and, in some cases, a surface with a defined lubricant. Standards Related to Slip-Resistance There are many different slip-resistance testing standards.

ASTM-F489 James Shoes Anti-Slip Tester

Hence, a low coefficient of friction indicates that only a low horizontal load would be needed to cause the shoe to slip against the flooring type used in the test.

Appendix Satm to this subpart references appropriate ASTM standard test methods that may be used to comply with this paragraph c 3. If you are a SATRA member but not yet registered for online access please register as a new user below. This method uses the stationary James Machine. This standard, rather than specifying a method, provides a framework under which tribometers can be validated.


The F48 Machine can still be used to test floor or shoe material, but has limitations of dry-testing only. Home About Us Our Staff.

The wet condition includes soap-contaminated specifications. Over this period, fundamental principles of slip have been identified, as well satm the characteristics of footwear required to reduce the risks of slip. View comments provided by High Safety Consulting Services. The method evaluates wet and dry conditions. The OSHA steel erection standards contained a provision for slip-resistance requirements for painted structural steel upon which ironworkers would walk.

To be meaningful, walkway tribometer results must correlate the slip characteristics of a surface or contaminant, or both, to the actual propensity for human slips. Rise height and tread width shall be uniform throughout any flight of stairs including any foundation structure used as one or more treads of the stairs. In addition, this method would generate sticktion problems on wet surfaces, so it is not recommended for evaluating wet slip-resistance.

ASTM Slip-Testing Methods – HighEHS

ASTM F To be meaningful, walkway tribometer results must correlate the asym characteristics of a surface or contaminant, or both, to the actual propensity for human slips. To achieve this goal, walkway tribometer models must be validated against a standard with relevance to human ambulation.

The footwear is mounted on a foot forme which, in turn is mounted onto the loading frame. The method can be used on nearly all surfaces. By using a standard test surface, and with reference to acceptable required minimum and maximum coefficients of friction, the footwear can be assessed for slip resistance.

Some product manufacturers incorrectly point to this proposed standard as a rule to which employers must comply.